Spring Design Calculators

Free tools for engineers specifying or designing springs. Get accurate answers in seconds — no account required.

4 Working Calculators Vanilla JS — No Dependencies ISO 9001:2015 Certified Manufacturer

Calculate. Check. Specify.

Click any card to open the calculator.

Spring Rate Calculator
Calculate spring rate (k) using the Wahl formula from wire dimensions, or derive it from two load-at-height points.
Wire Dia (d)0.148 in
Mean Dia (D)1.250 in
Active Coils8.5
Rate (k)→ 42.3 lb/in
Load @ Height Calculator
Enter free length, spring rate, and a target height to get the exact load the spring exerts at that position.
Free Length3.500 in
Rate (k)60 lb/in
Target Height2.750 in
Load→ 45.0 lb
Clearance Checker
Verify Works In / Works Over radial clearances. Flags insufficient fit with pass / marginal / fail status.
ConfigWorks In
Bore Dia1.375 in
Spring OD1.250 in
Clearance✓ 0.0625"
RFQ Builder
A 4-step guided form that structures your spring spec so our team can quote accurately on the first pass. About 2 minutes.
Step 1Spring type + config
Step 2Dimensions + load
Step 3Material + finish
Step 4Qty + contact

Common design questions — answered instantly.

How the tools work — and how to read the results.

What is spring rate, and how do I calculate it?
Spring rate (k) is the force required to compress or extend a spring by one unit of distance — measured in lb/in or N/mm.
Use the Wahl formula for dimensional calculations, or derive it from two load points:

k = (Load₂ − Load₁) ÷ (H₁ − H₂)
k = (G × d⁴) ÷ (8 × D³ × Nₐ)

Where G = shear modulus, d = wire diameter, D = mean coil diameter, Nₐ = active coils.
How do I prevent spring buckling?
Buckling occurs when Free Length ÷ Mean Diameter exceeds 4. Use a guide rod, reduce free length, or increase mean diameter.
Check your slenderness ratio:

Slenderness = Free Length ÷ Mean Diameter

If >4: install a guide rod through the ID, redesign to a shorter/fatter spring, or split into two nested springs. If ends are free to rotate, the critical ratio drops to ~2.6.
What material should I use for my spring?
Music Wire for general indoor use. Stainless 316 for corrosive environments. Chrome Silicon for high-stress or high-cycle applications.
Music Wire — Best strength-to-cost for dry indoor applications under 250°F.

Stainless 302/316 — Moisture, salt, mild chemicals. Medical applications.

Chrome Silicon — High stress (>45% of tensile), fatigue-critical, elevated temp to 475°F.

Phosphor Bronze — Electrical conductivity required. Non-magnetic.

Inconel — Extreme temperatures above 550°F.
What’s the difference between Works In and Works Over?
Works In = spring inside a bore (OD drives clearance). Works Over = spring over a shaft (ID drives clearance).
Works In: Spring fits inside a hole or cavity. The bore limits OD. When compressed, OD grows — ensure at least 0.030" radial clearance minimum. Provide bore diameter on your spec.

Works Over: Spring slides over a rod or pin. The shaft limits ID. When compressed, ID shrinks — ensure at least 0.020" clearance per side. Provide shaft diameter.

Use the Clearance Checker tool above to calculate both automatically.
How do I specify spring load at height?
Give us two points: the height at which the load is measured and the force required. Two points let us calculate rate precisely.
Format your load spec like this:

L1 = 40 lb @ 2.500" height L2 = 70 lb @ 2.000" height
Rate = (70−40) ÷ (2.500−2.000) = 60 lb/in

You can also specify rate directly if known. Be consistent with units (inches or mm throughout).
What end type should I specify?
Closed & Ground (CG) for precision. Closed & Unground (C) for cost savings in non-critical applications.
Closed & Ground: End coils closed and faces ground flat. Better load distribution, improved squareness, required for stacked configurations and precision assemblies.

Closed & Unground: End coils closed but not ground. More economical, faster to produce. Suitable for most general-purpose applications where precise squareness is not critical.

If unsure, tell us the application and we’ll recommend the right end type.