Compression Springs Level 2 of 3 · Design & Engineering Guide

Compression Spring
Design & Engineering Guide

Designing the correct compression spring requires several key parameters. Providing these details early in the design process helps ensure optimal performance, proper fit, and efficient manufacturing.

1Material Selection

Material choice depends primarily on the environment the spring will operate in. Before selecting a material, consider these questions:

  • Will the spring be exposed to moisture or corrosive environments?
  • Will it operate in high temperatures?
  • Will the spring experience high cycle fatigue?
  • Are there weight, conductivity, or magnetic requirements?
Material Typical Use
Music Wire High strength, general purpose indoor applications
Oil Tempered Wire General mechanical applications
Stainless Steel (302, 316, 17-7PH) Corrosion resistance, medical, outdoor
Chrome Silicon High stress and high cycle applications
Phosphor Bronze / Beryllium Copper Electrical conductivity or corrosion resistance
Engineering Note

Our engineering team can help determine the best material for your specific environment. If you're unsure, include as much detail as possible about the operating conditions when requesting a quote.

2Works In / Works Over

Understanding how the spring interfaces with surrounding components is critical for determining the correct inside diameter (ID) and outside diameter (OD).

Works In (Inside a Hole)
Spring inside bore — OD drives clearance
  • Sufficient clearance between the spring OD and bore
  • Avoid friction or binding during compression
Works Over (Over a Shaft)
Spring over shaft — ID drives clearance
  • Proper clearance between ID and shaft
  • Preventing interference during operation

Proper fit ensures smooth operation and prevents premature wear or failure. Provide the bore diameter or shaft diameter in your quote request.

3Free Length

The free length is the overall length of the spring in its unloaded state. It is one of the most fundamental dimensions to specify.

Free length is important because it determines:

  • Initial installation conditions
  • Available working travel
  • Load characteristics during compression

Providing the desired free length helps ensure the spring fits correctly within the assembly from the start.

4Maximum Travel (Working Deflection)

Maximum travel refers to the maximum distance the spring will be compressed during operation. This value is critical for determining working stress, spring fatigue life, and solid height limitations.

Important: Solid Height

Solid height is the height of the spring when all coils are fully compressed and touching. A properly designed spring should not operate at or near solid height unless the application specifically requires it. Operating too close to solid height causes premature failure.

5Wire Size

If the spring is being specified as a dimensional component only, the wire diameter must be defined. Wire size affects spring strength, spring rate, load capacity, and fatigue performance. Wire size is typically specified in inches or millimeters.

6Spring Rate

If a spring must deliver a specific force over a range of motion, the spring rate must be defined.

The spring rate is the amount of force required to compress or extend a spring by a specific distance.

Typical units: Pounds per inch (lb/in) or Newtons per millimeter (N/mm)

Spring Rate Rate = Load ÷ Deflection
Example

A spring with a rate of 50 lb/in requires 50 pounds of force to compress the spring 1 inch. Spring rate determines how stiff or flexible a spring will feel in the application.

7Spring Load

In some applications, springs are designed to deliver a specific force at a specific height rather than a specific rate. Providing one or more load points allows engineers to calculate the proper spring rate.

Height Load
Free Length: 3.000" 0 lb (unloaded)
2.250" 75 lb
2.000" 100 lb

This means the spring exerts 75 pounds of force when compressed to 2.250 inches. The rate can then be calculated from these load points.

8End Type

Compression springs typically use one of two end configurations. The right choice depends on precision requirements and cost considerations.

Closed & Ground (CG)

Coils are closed and ground flat. Preferred for precision applications.

  • Improved stability
  • Better load distribution
  • Increased perpendicularity
Closed & Unground (C)

Coils are closed but not ground. Cost-effective for standard applications.

  • More cost-effective
  • Common in small mechanisms
  • Lower load applications

9Wind Direction

Wind direction refers to whether the spring is wound Right-Hand, Left-Hand, or is Optional. For most compression springs, wind direction does not affect basic function. However, it becomes important when springs must thread onto components, when nested spring sets require alternating winds, or when interfacing with specific mechanisms that have a preferred hand.

Default Recommendation

If wind direction is not functionally critical to your application, specify Optional. This gives the manufacturer the most flexibility and can reduce lead time.

10Surface Finishes

Surface treatments can improve corrosion resistance, fatigue life, or appearance. Most compression springs are supplied bare (as manufactured) unless a finish is specified.

Shot Peening Zinc Plating Nickel Plating Passivation Powder Coating Wet Paint Bead Blasting Black Oxide

Shot peening improves fatigue life by introducing compressive stress. Passivation is used for stainless steel to enhance corrosion resistance. Ask our team which treatment is right for your operating environment.

Ready to specify your spring?
Our engineers review every quote personally and respond within one business day.
Request a Quote →